Corona WeedDESTROYER featured image Weeding Tools

Corona WeedDESTROYER: Product Review


GPR RECOMMENDATION

Ease of Use:
Quality:
Performance:
Final Thoughts

Sturdy but too big and heavy for more petite gardeners who will probably prefer a lighter version of this tool without the large toe plate.

Overall Score 3.3

Available on Amazon

Buy It

Sadly, I have a lot of experience with weeds and have used many weed removal tools in the past in a futile attempt to conquer them. The Corona WeedDESTROYER says that it is intended to “Remove tough weeds”. Let’s see if it lives up to this claim.

PACKAGING

The WeedDESTROYER arrived by mail in a rather large cardboard box. The tool was wedged into the bottom of the box with cardboard and was topped with a sheet of plastic bubble wrap. Although the cutting blades were covered, one of the blades pierced the box; thankfully, the blade was undamaged.

WeedSLAYER-in-shipping-carton

The WeedDESTROYER came in a sturdy shipping box

Getting It Ready For Use

The WeedDESTROYER comes fully assembled but requires a little work to make it garden-ready. First, there is a large flat cardboard information sheet attached to the shaft. It is attached with zip-ties so scissors are required to remove the tight plastic bands.

WeedSLAYER-information-sheet

Product information sheet that came attached with the unit

Second, there are thick plastic caps over the two cutting blades at the bottom of the tool. I wasn’t able to remove these by hand since the caps caught on the ridged blades so I needed to again use my scissors. As careful as I was, the scissors left some marks on the blade which soon blended in after some use.

WeedSLAYER-blades-protected-for-shipping

The cutting blades were wrapped in protective sleeves for shipping safety

WeedSLAYER-blade-scratches

Scissors were required to remove the protective shipping sleeves, which left marks on the blades. The marks disappeared after several weed removals.

About the WeedDESTROYER

The WeedDESTROYER is constructed and used in the same manner as many other similar devices, but what sets the WeedDESTROYER apart is its claim of removing tough weeds. To do that, it’s larger and heavier than most stand-up weeders.

At 4.17 pounds, the WeedDESTROYER is appreciably heavier than other similar tools – in fact, it’s more than twice as heavy as many of its competitors. The shaft is thicker and heavier than others, and at 40 inches from handle to blade tip, it’s 4 inches longer than many similar types of tools.

The WeedDESTROYER has two thick blades at the bottom, each with a jagged edge. The blades are made of high carbon steel and are set 1 ½ inches apart.

 

 

The handles at the top are each over 5 inches long and have a Corona patented ComfortGel® grip. This grip is very spongy and very comfortable to hold onto. It is also slip resistant when used with sweaty or wet palms.

However, while the WeedDESTROYER handle has a nice large diameter, it’s not ergonomically designed as some other stand-up weeders and so becomes tiring to hold after extended use.

There is a weed release plunger on top of the handle. Simply depress the plunger to eject the weed from the cutting blades. The spring for the plunger is encased in the shaft, which should prevent the spring from getting fouled with dirt or rusting. This should lead to a longer spring life.

WeedSLAYER-handle-and-release-plunger

Detail of the ComfortGEL® handle and release plunger

The WeedDESTROYER has a three-inch toe plate to help push the blades into the soil. This is a nice addition when the soil is so compacted that you need to use it, and is large enough to step down on even when wearing thick-soled shoes or boots.

To use the WeedDESTROYER, center the blades around the base of the weed. Push the blades down as deep as possible into the soil while keeping the shaft vertical (if you tilt it too much it’ll be difficult to fully grab the weed’s roots). You can apply additional pressure with your foot on the toe plate if necessary (I generally didn’t find it necessary to use the toe plate).

Corona-WeedSLAYER-on-top-of-weed

Blades being inserted into soil around weed

Once the blades are firmly seated in the soil, rotate the handle in a clockwise direction at least 180 degrees. I found it worked best when rotated more than 180 degrees, as well as rotating the handle in both directions. The package directions say to “twist the handle toward you,” which is a bit unclear – does that mean turn it to the right, or to the left? Does it even matter? Now pull the tool upward and the weed will pop out of the ground, roots and all.

To eject the weed from the tool simply push down on the plunger on the top of the handle and the weed falls out.

You are left with a 1 ½-inch diameter, 3-inch deep hole in the ground. Corona recommends that you refill the hole with dirt and/or a grass plug as it is a little large to be considered an aeration hole.

WeedSLAYER-blades-fully-inserted-into-the-soil-around-the-weed

Blades fully inserted into the soil around weed.

Weeding Performance

In spite of claims that the tool will “remove tough weeds”, I found that many of the larger weeds were not fully removed and taproots were often broken off, leaving a piece to regrow into another weed.

Corona-WeedSLAYER-weeds-broken-off

Removed weeds, note some weeds are broken along with the taproot

I would have liked deeper blades to remove bigger weeds. To remove a weed you want to get all of the root and the 3 inch blade just isn’t deep enough for large weeds. After using it, I ended up with lots of half-removed weeds and broken roots.

I also found the toe plate annoying to use. Between the positioning of the blades and attachment of the toe plate, it is difficult to see the blades to line them up over the weed. You need to put the shaft at an angle and bend down to see how the blades are aligned with the weeds, which slows down the weeding process.

The Corona WeedDESTROYER leaves a large hole, which needs to be filled with dirt unless you are working in a planting bed where people don’t walk.

After two months of use, the Corona stand-up weeder is holding up well except for the bolts that attach the toe plate and blades; those bolts are all rusting.

WeedSLAYER-rusting-on-bolts

Rusting on bolts

WARRANTY

The WeedDESTROYER has a 10 year limited warranty against defects in materials and workmanship.

RECOMMENDATION

The Corona WeedDESTROYER is meant for tough weed removal and is built sturdy for this task. I like that the ejection spring is encased in the shaft, rather than exposed, and the large toe plate allows you to get your full weight behind it when weeding in hard or compacted soil. However, I did not find that it removes larger weeds any better than many of its lighter competitors, and the toe plate is so large that it obscures sightlines when trying to position the weeder. And, as a 5′ 5″ female, the WeedDESTROYER is too big and heavy for me, although it may work well for a taller, stronger person.

WHERE TO BUY

The WeedDESTROYER is available online and from Lowes for $24.98. It is also available from Corona directly on their website for $33.10 + $11.30 shipping.

Corona WeedDESTROYER
Note that it shows the old name of WeedSLAYER, but it's the same product

Last update on 2018-12-16 / Affiliate links / Images from Amazon Product Advertising API

Enjoyed This Review?

If you liked this review, please sign up for our email updates with reviews, how-to articles and gardening videos!

Disclaimer – GPReview would like to thank Corona for giving us a free sample to review. There was no expectation that it would be a positive review and we received no compensation for writing it. All opinions expressed here are those of the author based on personal experience using the product.

Please note that the Amazon links (and only the Amazon links) above are affiliate links. Should you choose to purchase products through these links, GPReview will make a small commission (at no extra cost to you) that helps to support this website and our gardening product reviews. Thank you!

Share Your Thoughts!

This site uses Akismet to reduce spam. Learn how your comment data is processed.